Evco c-pro micro Instrukcja Użytkownika

C-PRO MICRO PROGRAMMABLE CONTROLLERS HARDWARE MANUAL CODICE 114CPRUHWE03

C-PRO MICRO HARDWARE MANUAL Page 10 Connector 2: Connection for the parameter upload/download key and/or output for RS485 module and/or controller fl

C-PRO MICRO HARDWARE MANUAL Page 11 Connector 5: Connector for remote keypad and I/O expansion unit (CAN) Conn. Abbrev. Description C5-1 + Connect

C-PRO MICRO HARDWARE MANUAL Page 12 To install the C-PRO MICRO, proceed as indicated in the figures (points 1 and 2). To remove the C-PRO MICRO, us

C-PRO MICRO HARDWARE MANUAL Page 13 3.4 General characteristics Safety reference standards EN60730-1 Scope of the device A programmable electroni

C-PRO MICRO HARDWARE MANUAL Page 14 3.6 Electrical characteristics CPU Microcontroller 8 bit Program flash memory 128 Kbyte RAM for data memo

C-PRO MICRO HARDWARE MANUAL Page 15 Fan analogue output Type Voltage measurement range Voltage measurement accuracy Voltage measurement sensitiv

C-PRO MICRO HARDWARE MANUAL Page 16 4 The C-PRO MICRO user interface The display has 4 red-coloured digits (plus decimal points) and 16 icons of var

C-PRO MICRO HARDWARE MANUAL Page 17 Maintenance icon Colour Red Alarm icon Colour Red Icon 1 Colour Green Icon 2 Colour Green Icon 3 Colour Green

C-PRO MICRO HARDWARE MANUAL Page 18 5 C-PRO EXP MICRO I/O expansion units The C-PRO EXP MICRO I/O expansion units allow expansion of the controlle

C-PRO MICRO HARDWARE MANUAL Page 19 5.1 The C-PRO EXP MICRO wiring layout (IntraBus version) The references to connecting cable lengths reported in

C-PRO MICRO HARDWARE MANUAL Page 2 Important Please read these instructions carefully prior to installation and use, and follow all the

C-PRO MICRO HARDWARE MANUAL Page 20 Connector 2: Connector for low voltage signals Conn. Abbrev. Description C2-1 12 V AC (Power) Device power sup

C-PRO MICRO HARDWARE MANUAL Page 21 5.2 C-PRO EXP MICRO dimensions/installation The mechanical dimensions for the C-PRO EXP MICRO are given below

C-PRO MICRO HARDWARE MANUAL Page 22 6.1.1 V LEDi dimensions and installation For panel installation, use the snap-on brackets provided Local p

C-PRO MICRO HARDWARE MANUAL Page 23 The user interface has a 7 segment, 4 digit display (plus decimal point), 6 icons and the user mode is achieved u

C-PRO MICRO HARDWARE MANUAL Page 24 6.1.2 V WALL dimensions and installation For wall installation, use appropriate rawplugs and screws. Wall-m

C-PRO MICRO HARDWARE MANUAL Page 25 Connector CI2: Terminal connector powered by a separate transformer Conn. Abbrev. Description CI2-1 12 V AC Re

C-PRO MICRO HARDWARE MANUAL Page 26 The user interface has a 7 segment, 4 digit display (plus decimal point), 6 icons and the user mode is achieved u

C-PRO MICRO HARDWARE MANUAL Page 27 6.2 Remote User interface (CAN) The user interfaces allow to install a display and keyboard remotely far from t

C-PRO MICRO HARDWARE MANUAL Page 28 The following table summarizes the keyboard button meaning: BUTTONS MAIN FUNCTION SECONDARY FUNCTION Predefi

C-PRO MICRO HARDWARE MANUAL Page 29 6.2.1.2 V-VIEW wiring layout 6.2.1.3 V-VIEW specifications General specifications Safety standards referen

C-PRO MICRO HARDWARE MANUAL Page 3 Contents 1 INTRODUCTION...

C-PRO MICRO HARDWARE MANUAL Page 30 Type CAN V2.0B not optoisolated Physical Layer 2 wires + common, ISO 11898 standard Baud rate (L max. = 10 m)

C-PRO MICRO HARDWARE MANUAL Page 31 6.3 EVDFAN1 cut-off speed regulator The EVDFAN1 is a cut-off speed regulator for controlling single-ph

C-PRO MICRO HARDWARE MANUAL Page 32 Terminals 1 and 2: Control input connector (Phoenix pull-out) Conn. Abbrev. Description 1 12 V DC 12 V DC powe

C-PRO MICRO HARDWARE MANUAL Page 33 6.4 Supervision and monitoring accessories These modules allow the conversion of TTL signals to RS485

C-PRO MICRO HARDWARE MANUAL Page 34 EVIF21TS7I connections Insulated interface wiring diagram Connector Conn. Abbrev. Description 11 + RS485

C-PRO MICRO HARDWARE MANUAL Page 35 6.5 Programming accessories 6.5.1 EVKEY programming key The EVKEY programming key allows downloading/upl

C-PRO MICRO HARDWARE MANUAL Page 36 7 CAN Connection C-PRO MICRO can be connected to other controllers, to expansion modules and to one or more user

C-PRO MICRO HARDWARE MANUAL Page 37 7.1 Notes on the parameter of the controller relative to the CAN net configuration To log on the controller p

C-PRO MICRO HARDWARE MANUAL Page 38 The main parameters of the CAN net are the following : • “My Node” (represents the data sender ID ) • “Network

C-PRO MICRO HARDWARE MANUAL Page 39 C-PRO MICRO hardware manual. Version 1.03 January 2009. Code 114CPRUHWE03. File 114CPRUHWE03.pdf. This document i

C-PRO MICRO HARDWARE MANUAL Page 4 1 Introduction The C-PRO MICRO family of programmable controllers is the ideal solution for refrigeration, venti

HEAD OFFICE Evco Via Mezzaterra 6, 32036 Sedico Belluno ITALY Tel: 0437-852468 Fax: 0437-83648 [email protected] www.evco.it OVERSEAS OFFICES Control

C-PRO MICRO HARDWARE MANUAL Page 5 2 Component and auxiliary network systems 2.1 Example for the built-in versions

C-PRO MICRO HARDWARE MANUAL Page 6 2.2 Example for the sealed case versions

C-PRO MICRO HARDWARE MANUAL Page 7 3 Technical characteristics 3.1 Connections Power supply: The C-PRO MICRO is powered by a 12 V AC supply. It

C-PRO MICRO HARDWARE MANUAL Page 8 Connection with a remote expansion (or another CAN controller): The connection between C-PRO MICRO and the remote

C-PRO MICRO HARDWARE MANUAL Page 9 3.2 The C-PRO MICRO wiring layout The C-PRO MICRO control unit wiring layout is shown below, with the meanings o