Evco c-pro nano Instrukcja Użytkownika Strona 1

C-PRO NANO PROGRAMMABLE CONTROLLERS HARDWARE MANUAL CODICE 114CPRNHWE03

C-PRO NANO HARDWARE MANUAL Page 10 3.3 C-PRO NANO dimensions/installation The mechanical dimensions for the C-PRO NANO are given below; the measur

C-PRO NANO HARDWARE MANUAL Page 11 3.4 General characteristics Safety reference standards EN60730-1 Scope of the device A programmable electronic

C-PRO NANO HARDWARE MANUAL Page 12 3.6 Electrical characteristics CPU Microcontroller 8 bit Program flash memory 128 Kbyte RAM for data memor

C-PRO NANO HARDWARE MANUAL Page 13 Fan analogue output Number 1 Type EVCO impulse cut-off UART1 TTL Number 1 for RS485 serial port Type UART

C-PRO NANO HARDWARE MANUAL Page 14 4 The C-PRO NANO user interface The display has four red-coloured digits (plus decimal points) and 16 icons of va

C-PRO NANO HARDWARE MANUAL Page 15 Maintenance icon Colour Red Alarm icon Colour Red Icon 1 Colour Green Icon 2 Colour Green Icon 3 Colour Green

C-PRO NANO HARDWARE MANUAL Page 16 5 C-PRO EXP MICRO I/O expansion units The C-PRO EXP MICRO I/O expansion units allow expansion of the control

C-PRO NANO HARDWARE MANUAL Page 17 5.1 The C-PRO EXP MICRO wiring layout (IntraBus version) The references to connecting cable lengths reported in c

C-PRO NANO HARDWARE MANUAL Page 18 C1-12 COMMON DO6 Relay No.6 - common Connector 2: Connector for low voltage signals Conn. Abbrev. Description

C-PRO NANO HARDWARE MANUAL Page 19 5.2 C-PRO EXP MICRO dimensions/installation The mechanical dimensions for the C-PRO EXP MICRO are given below;

C-PRO NANO HARDWARE MANUAL Page 2 Important Please read these instructions carefully prior to installation and use, and follow all the

C-PRO NANO HARDWARE MANUAL Page 20 6.1.1 V LEDi dimensions and installation For panel installation, use the snap-on brackets provided Local pan

C-PRO NANO HARDWARE MANUAL Page 21 The user interface has a 7 segment, 4 digit display (plus decimal point), 6 icons, and the user mode is achieved us

C-PRO NANO HARDWARE MANUAL Page 22 6.1.2 V WALL dimensions and installation For wall installation, use appropriate rawplugs and screws. Wall-mo

C-PRO NANO HARDWARE MANUAL Page 23 Connector CI2: Terminal connector powered by a separate transformer Conn. Abbrev. Description CI2-1 12 V AC Rem

C-PRO NANO HARDWARE MANUAL Page 24 The user interface has a 7 segment, 4 digit display (plus decimal point), 6 icons and the user mode is achieved us

C-PRO NANO HARDWARE MANUAL Page 25 6.2 Remote User interface (CAN) The user interfaces allow to install a display and keyboard remotely far from th

C-PRO NANO HARDWARE MANUAL Page 26 The following table summarizes the keyboard button meaning: BUTTONS MAIN FUNCTION SECONDARY FUNCTION Predefin

C-PRO NANO HARDWARE MANUAL Page 27 6.2.1.2 V-VIEW wiring layout 6.2.1.3 V-VIEW specifications General specifications Safety standards referenc

C-PRO NANO HARDWARE MANUAL Page 28 Type CAN V2.0B not optoisolated Physical Layer 2 wires + common, ISO 11898 standard Baud rate (L max. = 10 m)

C-PRO NANO HARDWARE MANUAL Page 29 6.3 EVDFAN1 cut-off speed regulator The EVDFAN1 is a cut-off speed regulator for controlling single-pha

C-PRO NANO HARDWARE MANUAL Page 3 Contents 1 INTRODUCTION...

C-PRO NANO HARDWARE MANUAL Page 30 Terminals 1 and 2: Control input connector (Phoenix pull-out) Conn. Abbrev. Description 1 12 V DC 12 V DC powe

C-PRO NANO HARDWARE MANUAL Page 31 6.4 Accessories for supervision and monitoring These modules allow the conversion of TTL signals to RS485 signals

C-PRO NANO HARDWARE MANUAL Page 32 EVIF21TS7I connections Insulated interface wiring diagram Connector Conn. Abbrev. Description 11 + RS485+

C-PRO NANO HARDWARE MANUAL Page 33 6.5 Programming accessories 6.5.1 EVKEY programming key The EVKEY programming key allows downloading/uplo

C-PRO NANO HARDWARE MANUAL Page 34 7 CAN Connection C-PRO NANO can be connected to other controllers, to expansion modules and to one or more user i

C-PRO NANO HARDWARE MANUAL Page 35 7.1 Notes on the parameter of the controller relative to the CAN net configuration To log on the controller pa

C-PRO NANO HARDWARE MANUAL Page 36 The main parameters of the CAN net are the following : • “My Node” (represents the data sender ID ) • “Network N

C-PRO NANO HARDWARE MANUAL Page 37 C-PRO NANO hardware manual. Version 1.03 January 2009. CODE 114CPRNHWE03. File 114CPRNHWE03.pdf. This document is

HEAD OFFICE Evco Via Mezzaterra 6, 32036 Sedico Belluno ITALY Tel: 0437-852468 Fax: 0437-83648 [email protected] www.evco.it OVERSEAS OFFICES Control

C-PRO NANO HARDWARE MANUAL Page 4 1 Introduction The C-PRO NANO family of programmable controllers is the ideal solution for refrigeration, ventila

C-PRO NANO HARDWARE MANUAL Page 5 2 Component and auxiliary network systems

C-PRO NANO HARDWARE MANUAL Page 6 3 Technical characteristics 3.1 Connections Power supply: The C-PRO NANO is powered by a 12 V AC supply. It m

C-PRO NANO HARDWARE MANUAL Page 7 Connection with a remote expansion (or an other CAN controller) : The connection between C-PRO NANO and the remote

C-PRO NANO HARDWARE MANUAL Page 8 3.2 The C-PRO NANO wiring layout The C-PRO NANO control unit wiring layout is shown below, with the meanings of t

C-PRO NANO HARDWARE MANUAL Page 9 Connector 3: Analogue output connector Conn. Abbrev. Description (V+I version) C3-1 AO2 0-10 V DC C3-2 GND Co